Hardware Controller (OC200) – SDN Integrated, Powered, Manages up to 100 Devices, Intelligent Network Monitoring, Cloud Access, App Support

In the attached photograph, the OC200 is the device on the left. TP-Link Omada equipment is primarily marketed to business. I am using it in a home network. I am using it to control three ceiling mounted TP-Link EAP610s (fed by the red patch cables in the PoE switch on the right) and an ER605v2 router. The OC200 is powered by PoE (it can also be powered by USB) reducing power cable management needs, and once set up, it just runs and lets you administer Omada devices without the need to have a software controller running is a 24/7 powered PC or a need for cloud management. The user interface (web based) can be a little confusing to figure out, but there is a fairly detailed PDF user manual you can download. It can do much more than I am using it for, I am using it to manage three ceiling mount EAP610s in a large house. First we just installed one to see how it went, and when it worked well we ordered the other two, importing them was literally a click of a button and they were configured to integrate with the settings used for the first. The controller makes management of the wireless network a breeze and it's designed so you can automate backup to a USB key so that if the unit ever fails, you can restore to a new unit from the backup (devices under it's control will continue to work if it fails, but you won't be able to change configurations until a new one is in place and restored) It could be argued it is too powerful and complex for a home network but if you are technically inclined, with a little help from online communities and the manual, it isn't too difficult to figure out. It's a good system.

Real Title: Omada Controller, UniFies your Omada Access Points and enabled Cloud Access, to make on Ubiquitous network solution. I've set these units up for a number of families in my neighborhoods, in conjunction with EAP225 Access Points, and a PoE Switch to power it all. The Omada setup is a great discount alternative to the Ubiquiti Networks UniFi Access Points and Switches. It's cheaper and works just as well. For a residence, I'd say it's a fantastic option. And it's a breeze to configure, assuming you have enough background in the area to know the ropes. PRO: +inexpensive! Can be run on a computer instead but, at this price, just set up the hardware controller, jeez. +PoE, with Micro USB as an alternative power option. +Super tiny! my gosh, the thing is half the size of an 8-port switch (see my photo, it's on top of a TP-Link switch and router) +Super easy cabling with a PoE Switch (1 cable to do all jobs) +Supports 100 Omada Access Points, which is more than any residence could possibly need. CON (honestly none): -Not free (but there's free software that can be equivalent to this!) -uses Micro USB instead of Type-C (holy cow is that a nitpick if ever I heard of one) -doesn't include a power cable? Only includes a short patch-cable, assuming that you already have PoE or Micro USB. -doesn't include mounting hardware to bolt to a wall? -doesn't include a sandwich to enjoy while you do your configuration? -probably impossible to properly rackmount.

I really like the user interface with the controller. It allows me to see everything and more on my home mesh network. Ya, maybe it is a bit of overkill since my network only has four APs but the mesh has worked seamlessly for all of our devices and resolved the network congestion and latency. Plus having multiple APs in the house and one outside has really expanded the network coverage. I even have an IoT device in the chicken coop that stays connected solidly! I would not have been able to configure this mesh network with all of my tp-link devices easily, if at all, without this controller. The controller was very intuitive to set up and easy to connect with PoE to the PoE+ switch. Like I was saying though, it really is overkill for my little network. This controller appears like it could be used for commercial or industrial use for multiple location. But the price and ease of installation and configuration made this purchase a no brainer for me. I have had this controller running my network with its six SSIDs for about three weeks with no issues so I would recommend it.

The TP-Link Omada Hardware Controller (OC200) is an excellent network management solution for anyone looking to gain more control and intelligence over their home or business network. With SDN integration, PoE power, cloud access, and the Omada app, it provides everything you need to manage and monitor your network easily and efficiently. The setup is simple, the performance is reliable, and the advanced network features are perfect for those who need flexibility and scalability. I highly recommend it for small to medium-sized networks, whether for home or office use!

The controller is an integral part of the Omada setup for Wireless control and optimization, so I added the controller. Overall it works just fine, it's a bit slow to log into and switch screens sometimes, but overall it works just fine. I think it's fantastic that TP-Link fully supports Linux/UNIX software, so if you desired you could easily build your own controller. That is one of the many reasons I love TP-Link. You get decent hardware, that functions overall very well, with some config flow problems, but overall you get good performance and hardware. I got the controller just to save time, maybe in the future I will build a raspberry pi into a slightly faster controller. Overall I'm happy.

I bought the OC200 since I was so impressed with EAP670 V2 but realized I needed to manage them all and OC200 job was to specially do this at scale. So I bought it and was pleasantly surprised at the rice feature set and ability to upgrade and scale configuration out to all the access points simultaneously. I did have to upgrade the SDN software which was both feature rich and very stable, once you installed the latest version. I was equally impressed with EAP670 V2 which just worked flawlessly and kept my WiFi connections for all my wifi devices old or new, I can't stress how good that felt after coming from so many other WiFi routers from many many other brands. This just worked connected everything, was super stable with WiFi connections and devices that just stayed online without any issues - wow WiFi that just works isn't that how it supposed to be?!? I had turned on mesh so that devices would connect to strongest signal but would caution not turning on full roaming since some devices may not be compatible and fail to connect or roam properly, the defaults work just fine though. I've had this setup for over a month and things are just super stable. I've even done upgrade with OC200 and that worked flawlessly, very happy with this setup and since my EAP670 V2 supports WiFi6 I should be good for long time. Whilst WiFi7 is around the corner hardly anything uses and needs WiFi6, I suspect WiFi7 will be several years away that I'm not worried about that at all and would rather have stable WiFi for all my WiFi 4/5/6 devices right now.

In short, I had a lot of problems with my TP-Link AEP245 access points before getting this, and now I don't. This is a better alternative to a mesh system if you have ethernet in a few spots in the house. I have a large house and a large number of smart devices. I was having a hard time getting good wireless signal in remote corners of the house and my router kept failing because of too many wifi clients. I thought about getting a mesh system, but since I have ethernet in several spots across my house, I would have used the ethernet backhaul anyway. No need to use a mesh system, which is designed to send info wirelessly from device to device at a slower speed. Instead I decided to do what is done in commercial contexts: just use several access points. I purchased three TP-link AEP 245 access points and set them up in a way that gets coverage all over the house. It worked OK, except I kept having problems with devices that roam, like cell phones. They wouldn't let go of one and go to the other. Or something. They always said they were connected but some of the time no internet would get through. The AEP245 is supposed to work in standalone mode when you do this as long as you set them all up with the same SSID, password, and settings, but on different channels. Unfortunately, I cannot recommend them for that configuration. I decided as a last ditch effort to buy this controller. It advertises the ability to use fast roaming technology to tell certain roaming devices to go from one access point to the other as you walk around. Anyway, it did actually solve my problem. You can now walk all over my house with whatever device you want and it will always work. It never goes down, the speeds are awesome, and it was easy to configure and to maintain. To be honest, I'm not actually sure whether my system is using 802.11(k/r/v) or some other technology. All I know is that I had tons of problems with my wifi before getting this, and now I don't. It's a little hard to explain what this device does and TP-Link doesn't make it obvious. It does take control of all your access points and let you configure them from a central location instead of having to connect to each individually. I don't think of that as a huge deal. It allows you to monitor all the clients on all access points and see which is downloading how much, disconnect them, and do all sorts of other stuff. Actually, besides the monitoring of bandwidth and clients and allowing central configuration, it's hard to identify what this really does that you can't do in standalone mode without any controller. However, I can tell you that the internet experience is 100% better with this controller. I don't really understand why it's necessary or exactly how it works, but I'm really glad I got it. I recommend it to anyone who is using multiple TP-Link access points

I bought these for a Wedding Venue in Rome, Georgia Proctor Farm. Total coverage is at least 800 feet from the main house with Trees and bushes blocking some views. My setup is 1 OC200 Omada Controller and 3 EAP 225 Access Points with a VERY slow (Maximum speed for our rural area) from AT&T internet of only 18mpbs. 1. Main Access point: at the house, wired with an ethernet cable, and upstairs outside on the 2nd-floor balcony, I upgraded the antennas from the stock 3dbi to (Kaunosta 2.4 GHz 22dBi WiFi Antenna) - This one access point covers the entire house and the entire outdoor ceremony area. 18 MPBS here at full speed (Up to 100 devices can connect on this access point) 2. Downlink to the Chapel about 250 feet one tall shrub is blocking the direct line of site (This 2nd access point covers the Chapel, Pavillion (eatery area) and overlaps with the outdoor ceremony area. About 17 MPBS at this distance (Up to 100 devices can connect on this access point) 3. Downlink to Saloon about 100 feet from The Chapel, not in direct sight so we went UP about 12 feet into a tree, camouflaged the power cord and POE box that runs to AC box at the saloon for power. This 3rd Access point covers the Saloon and overlaps with the Pavillion and entrance of the Venue. About 15 MBPS at this distance (Up to 100 devices can connect on this access point) It is important that you take the time and UPDATE the firmware if ANY needs to be done for any access point or controller you have. Takes about 10 - 15 min and will save you from a world of dropouts and trouble DO THIS FIRST! With the Controller we were able to add a Guest Wifi landing page to promote our business just like major hotels and restaurant chains use. We are also now able to have 5 cameras solar powered spaced through the property both indoors and outdoors thanks to this setup. We called TP-Link to get help adopting the 3rd access point and we simply needed to update the FIRMWARE and create a proper downlink system: 1. Home 2. Chapel 3. Saloon Thanks to Miraflor Salvador (Mira) who walked us through everything carefully and got us fully up and running.