ECOTRIC Hitch Cargo Carrier with Ramp Foldable Hitch Mount Wheelchair Carrier Mobility Scooter Ramp 500 lbs Weight Capacity

Anyone looking at this item be very very aware that this is definitely a two man lift and a 3 man to fit it And it’s taken me nearly a month to have it collected Buyer be aware

I bought one of these last year 2023 for a really good price from Amazon. It’s a tad heavy but super strong the ramp is a good weight and folds vertical or flat depending on what you are carrying, big tick! I have a mobility scooter which goes on quite easily but just wish it was made to be 120cm in length. Also I found it a little low to the ground when on a gradient, however I overcame this by buying an offset 2 inch receiver adapter which raises the whole thing approximately 6 inch higher. Don’t know why we don’t see more of these as they are a lot easier to store than a trailer plus it overcomes the tip bylaws of no trailers. W Broadley. Blackpool.

Thanks for the great craftsmanship!

I have not put it together yet but in box it is very heavy. My son is guessing 60 lbs. I would say 60-100. I found another like it same price but receiver part was steel but rest was aluminum. This 1 is all steel. In reviews 1 guy said he had to weld a peace to make it work on his Trk. Well U can't weld Aluminum to steel so I got this 1. Also if it should crack or need repair U can weld. I got it to take snow blower over to my sons when needed and hall my red trailer on with grass for garden. This will be much easier than the bigger trailer. OK I put it together and on the trk. It is very well built but instructions need some help. It tells what bolts go where and the pins. I took it apart 2 times and put it together 3 times. 1rst I put the Tung on wrong. U want the ramp to drop on passenger side so pay attention to hinges. Only 1 of 2 ways to do it I did it wrong. Than there is 2 bolts. 1 long and 1 short. Long 1 goes through tung and piece that goes into trk hitch. Short 1 goes into threaded hole under it to level. On tung there is a small piece of steel welded on bottom of tung for added strenght. It was used but not needed. There is a pin with S pin for it. So with long bolt and pin there is no leveling. Maybe to lock it? Well I did that wrong also. 3rd times a charm. The piece to pin the ramp up and down I had to put about 6 washers to move it out cause ramp was 2 close to frame. I got the ramp at a 90 degree pin to line up but 1 that pins it down to platform I need to drill out bigger for adjustment for lower pin to lock ramp in a not in use mode. Also none of it is not standard. Most metric and some don't know. Ended up using 2 crescent wrenches. It is heavy. I took out of box in house read instructions and took out in pieces in morning. It took me all day to assemble and on trk so still need to drill hole out. Now I could put together in couple hrs. I would buy it again but see no need to. It will do what I want to. I also went back to amazon's add and took some picks with phone so I could enlarge and see better. There is a small bag with blk nuts and washers. Put in pocket. I didn't see and wind blew away along with instructions. Found latter when done. Also peace that goes into trk hitch has a added piece welded on for wear. The tung should set down from top. LOL I hope this will help U do it in 2 hrs and not all day. Also the reflectors are very small. I got 2" X 50' here on amazon will put bigger and more than what they sent. Only thing is that my trk sets high but I can pull up on street and drop past the curb gaining 4-6" on ground height. Good luck.

Not the greatest to assemble but I knew that from the reviews. The best advice I can give is get it into your receiver first then finish assembling it and you will have less problems. I love this thing, it's made my weekly doctor visits quick and painless. I can go to the mall now without trying to get my scooter in and out of my mini van with ramps. This model folds up good and right to the back window. Good stuff. We had some leftover nuts and washers. Update 1 year later now. I had to add carabiner to the front and back holes to use my ratchet tie down for my mobility scooter. Wish the ramp was 1 foot longer but it does exactly what I need which is haul my scooter daily. Get a can of WD 40 to go with it and keep the moving parts well lubed

I bought this to haul a snowblower. It did the job just fine. After reading other reviews, I was worried about the assembly. The instructions were OK. They could be better, could be worse. Took about 30 minutes to assemble. I am glad I got one with a ramp. It does take a rather large wrench. I did not have the correct size socket, so I used a crescent wrench. I am not sure what size you need.

First, the tray's inner dimensions are 26 1/8" x 46 1/8" NOT the 28"x50" nor the 26.38 X 46.85" as listed. I would not have purchased this had the dimensions been accurately listed. Second, the assembly instructions are HORRIBLE. It's as if the person writing the instructions was trying to omit as many steps as possible and the ones that made it were written originally in Chinese translates to Turkish using google translate and then again into English. This matters for several reasons. First, the bolts used to attach the tray to the main structural support have lock-nuts that are single use. I put the main structural support bar on upside down (yes, there is a top and bottom even though that's not indicated in the assembly instructions) but had to buy my own grade 5 3/8" bolts with lock-washers. Second, it's easy to switch several similar looking parts if you didn't pay attention to the pictures here on Amazon (which are much clearer than the ones in the instructions). There are also parts that someone without significant experience with this kind of device would know how to use at all - like the set bolt that determines the angle between the hitch and the tray. I would not only not buy this product again or recommend it to anyone, I wouldn't buy from this manufacturer again.