Official Space Pi Filament Dryer Plus, 2 Rolls 3D Printer Filament Dryer Box 360° Hot-Air Heating with Fan, Upgraded Filament Dehydrator Storage Box for 1.75/2.85mm PLA PETG ABS TPU Material

I’ve been 3D printing for a while and finally decided to invest in a proper filament dryer, and I’m really glad I chose the Creality Space Pi Filament Dryer Plus. The build quality is solid, and it looks great on the workbench. One of the best features is the capacity for two spools, which is perfect for longer prints or keeping multiple materials dry and ready to go. It fits standard 1.75mm spools easily, and the interior space is well-designed. Drying performance is excellent. The 360° hot-air circulation and built-in fan really make a difference. I noticed improved print quality, especially with hygroscopic materials like PETG and TPU. It’s also very quiet in operation compared to my previous Sunlu S2 dryer, which is a bonus if you’re working in the same room. The temperature and timer settings are easy to use, and the display is clear and responsive. It gives you full control over the drying process depending on the material you're using. I've been running it for several hours at a time, and it keeps the temperature consistent throughout. Overall, this dryer is a great addition to any 3D printing setup. It does exactly what it's supposed to, and it does it well. If you’re serious about print quality and want to protect your filament from moisture, this is absolutely worth the investment.

I wanted a dry my PET CF filament, and yes the tempteatures this unti can reach are too low, 65 deg C when I needed higher. But that side it would work for the other various filaments I use so it would be useful regardless. The good news was my printed PEF CF parts went from ragged and rough to a fantastic textured surface with no visable layers after drying for 12 hrs at 65 deg C. So it does exactly what I wanted. Another bonus is it can dry two filaments at once and be used as an external spool while keeping the filament dry and warm while printing. Pretty sure this is where the previous (8hr plus) attempts to print PET CF failed as the layers got progressively worse. Sits neatly beside my Bambu Carbon like its mini me. Nice modern clean design. Comes with two nylon tubes that can feed from the top or 45 degrees to the rear into your printer. The down side is the touch screen controls, they are not great and dont always work correctly resulting in switching off, waiting a while and switching back on again. This is such a shame because otherwise this is a great product.

works well, improved print quality consistency

does the job as expected, definitely noticed improved quality after drying the filament.

Keeps my filament perfect. Silent in use.

Nice looking unit works well and easy to setup to run ( good job as they provide little guidance) My issue was as it was supplied directly to me from uk wheat house it was delivered just in its box no cover wrapping and a postage address label stuck to the side, there was not every tape sealing off the box’s opening lid. Was obvious some one between the wear-house and my house had opened the box to see what’s in there as items were not packed where they should have been.

A good idea to keep rolls dry but actually quite expensive for what it is, and not big enough now for my growing filament collections

This is a neat product that takes two reels and dries them well. The control panel takes some getting used to as the finger pressure has to be just right. Once you get the hang of it it is OK. Biggest issues is that if the temperature is less than 15C when powering up, it reports an error and refuses to heat. In my workshop which is unheated I have to use a hot air gun to waft some warm air into the unit to get it to start.

Great filament drier. Useful 48 hour timer and space for two reels. The bearings are a bit noisy starting up but the unit works great.

Funktioniert tadellos. Der Kreislauf beim trocknen erreicht alle Stellen

Desde que utilizo el secador de filamentos,las piezas quedan sin defectos.Vivo en la costa,y hay mucha humedad.

tiene due bobine, ha le uscite per il prelievo e i rulli. perfetto per tpu e altra roba disperatamente igroscopica

منتج اصلي يحافظ على خيوط الطباعة من الرطوبة وتغير درجات الحرارة يقبل منتجين مختلفة