ELEGOO ABS-Like 3D Printer Resin 3.0, 405nm UV-Curing Photopolymer Resin for LCD/DLP 3D Printing, with Enhanced Strength and Toughness, High Precision, Low Viscosity, Grey 1000g

This is a great resin for 3D printing in great detail. New users will be surprised at the level of detail that can be achieved on prints. It comes well packaged by Elegoo and also by Amazon. This is required because spilled liquid resins have some serious side effects if you don’t use the correct PPE and disposal methods of waste resin. Neither should waste resin from spills or cleanup be tipped down the drain uncured, research the correct ways to dispose of it. It’s important to not let uncured resin touch your skin anywhere at any time. Some of the risks include skin irritation, allergic reactions and respiratory issues, so it’s important to use the right type of filtration on your respirator set up. You must also consider the welfare of every other person and animal living in the house, fish tanks especially. The toxic VOC, Volatile Organic Compounds run a high risk of respiratory infections. A useful purchase is an Air Quality meter, which includes a TVOC readout so you know your filtration and disposal of fumes is working effectively. Available from Amazon. Safety must come first. With that in hand enjoy using this resin

Really good resin worked well in my printer great company to deal with

This resin is super tough, can be difficult to remove from the build plate and remove supports, but worth it for the benefits. It not only resists bending but it is super strong too. It was easy to calibrate and on my printer I've printed about 4 litres of it now without a single failure. The only downside is that it is quite smelly. I don't mind that so much as I have a vented to outside enclosure.

I have tried all sorts of resins in the past and this particular one is by far best I’ve used so far. The level of detail produces is fantastic and is relatively easy to clean with the help of IPA , I haven’t had any issues with curing I.e. splitting etc. The rest in itself isn’t overly smelly however I do use an extraction unit while it’s printing and face mask dealing with uv resin. It’s not brittle like some other ABS resins so great for miniatures.

Great resin, the 3.0 pro series is one of the best ones I used, especially in UK where its colder during winter, as other resins tend to warp. 4/5 Stars for this one, due to labeling. I often keep 5 or so boxes of different colours. The colours are usually labelled on the box, but with transparent resins, only the "Translucent" box is indicated, so when I have 4 different colours of transparent resins, there is no indication on the box which transparent colour it is. It does say it on the bottle, but I had to open 4 boxes before I found the one im looking for...

A good 3d printer resin. No issues what-so-ever. Will buy again.

This has very much earned its spot as my go to resin

works as intended!

Ottima resina, presa in sconto e quindi con un rapporto qualità prezzo imbattibile. Avrei preferito una water washable ma per questo prezzo mi accontento

good abs-like resin, does what it says, perfect results every time, cheap for the amount too. using chitubox pro and the elegoo mars 5, the perfect combination

Man liest einiges im Internet über v3, und nicht alles ist positiv. Ich kann allerdings aktuell nichts Negatives sagen - Ich bin mit meinem Mars 3 Pro bei 2,3 Sekunden exposure, was weit unter dem empfohlenen Wert von 2,8-3,2 ist. Der/die/das Resin wird schön hart, auch bei dünnen Teilen biegt sich da nichts, was ich persönlich sehr mag. Zwar brechen diese dünnen Teile dann schneller, aber ich mag einfach keine weichen Harze. Das ist aber sicherlich Geschmackssache. Nicht ganz so gelungen finde ich die Flaschenöffnung, die dürfte gerne etwas größer sein, dann würden auch die Filter besser passen, denn dabei muss man echt aufpassen beim Zurückkippen. Die üblichen Filter haben nicht nur eine Öffnung unten, sondern noch 2 zusätzliche rechts und links, und die passen NICHT in die Falsche. Wer hier zu schnell kippt, der kippt sein Harz von außen über die Flasche. Unangenehm. Ich möchte noch anmerken, dass ich das Harz auch als "anfängergeeignet" einordnen würde. Ich bin selbst Anfänger im 3D-Druck und alles funktioniert wunderbar, ohne irgendwelche verrückten Anpassungen. Nur nicht vergessen, zuallererst die Cones of Calibration zu drucken und alles sollte passen. Preislich mit rund 20€ ist das Harz auch noch absolut im Rahmen und für mich passt das Preis-/Leistungsverhältnis sehr gut.

Muy buena calidad y las piezas se notan mas resistentes.

Mooie kleur en fijn spul. De randen zijn na printen heel hard en scherp, mezelf al een paar keer raak gesneden.