3D Printer Glue Sticks, FENGWANGLI 4 Pieces Solid Adhesive for Hot Bed Print Filament PLA Glass ABS PETG CPE

I have a glass plate and within my first 2 or so small prints I was unable to start anything due to lack of adhesion. Every time I print I just scrape some of the glue off while it’s preheating and apply the new glue as it reaches a couple degrees from the target temps. This results in a funny texture on the bottom of my prints sometimes but I’m only printing little trinkets for myself right now so it doesn’t matter. Once it starts to build up after a few layers I take it off and wash it then it’s a lot smoother. I’m unsure if applying immediately before printing gives the best adhesion or not since I’ve never tried it otherwise but I can definitely say if you have a glass bed you should never have issues using this

If you go through these like crazy, you will love these. Easy removal and good adhesion to the bed.

So I feel like most of the negative reviews are from people that do NOT know how to use the glue stick, FIRST you will have to heat up your bed and nozzle (I use a glass bed) after your bed and nozzle has been heated up, you want to apply a layer of the glue evenly I usually just apply it all over the bed to cover the whole printing area, after you apply your layer of glue onto the bed you want to start printing RIGHT AWAY, if you let the glue sit there while your bed is heated it will DRY UP and will NOT work, this is why you want to start printing right away once your glue is applied, it has to be somewhat sticky and fresh for it to work properly, and I'm telling you I have done 30+ prints and NONE of them have failed me that first layer sticks it's so smooth and sometimes is really hard to come off once the print is done, I used to have so many adhesion problems on my printer and nothing would stick to the bed now that problem is SOLVED, keeping in mind that your bed is leveled properly and the reason I give it 4 starts is because there is glue for 3D printing and there is Regular glue, this to me just seems to be some cheap glue that you can get from the dollar store but its doing the work and it was cheap, by the way I apply glue on everysingle print and wash my glass bed with soapy water every 3 - 4 prints because the glue does add up onto your bed if you don't clean it, hope these tips help somebody out there and happy printing :).

good product good price

I started using these glue sticks after I started to have trouble getting my prints to stick to the build plate. It's very easy to clean off of any type of build plate also. Just hot water and soap and it comes right off with minimal scrubbing. I have kept these glue stick in stock ever since I started using them. It's a must have if you 3d print in my opinion.

Sticks a little, but not strong enough to hold detailed ABS prints. Lifting in several spots already - I’ll have to go back to the more expensive stuff. Did a decent job on some PLA grids I printed.

I've read about all kinds of binding agents (glue, hair spray, tape, rain dance, etc.) but for my lack of experience using these has helped me create some great prints. I still have a lot to learn and need to work on my temps (I'm getting good adhesion, but a bit of flow) so may be a temp issue. Not sure if I can use a name brand white glue stick, but for the price, these fit the bill. Most of my reviews are higher rated because I base what I purchase off of what I need, price, and quality, and not that I purchased the wrong item, or didn't read. I didn't have to reach out to the seller or the vendor, but I would not hesitate to purchase this product again, from either.

There's not much to say. It does the job. It's a good price for these big glue sticks and it's not too bad to clean up.

I had been using a certain "Elmer glue stick" forever. I ran out and discovered that product was almost impossible to source and what was available was now crazy priced!Found this product on Amazon, four stcks for the price of one of Elmer's , it's designed for 3D printers, let's give it a tryIt worked awesome ! A small diameter area tall print, no raft, no skirt, amazing!

ガラスステージにABSが密着しました。PLAはガラスに密着するのですが夏場の高温で変形してしまうのでどうしてもABSを使いたいと思っていました。今まではABSを使うためにはPEIシート等のステージシートを貼り付けて使うしか密着させる方法がなかったのが、ガラス表面にこれを塗るだけで見事に密着しました。

3Dプリンターで使用していましたとても頑丈に引っ付きますただ、あまりにも頑丈に引っ付くのであまり最近は使用していません最近はマスキングテープを張ればたいてい90％台座に引っ付くようになったのでPLA時はマスキングテープのみを使用しています、ABSは台座にとにかく引っ付かないのでマスキングテープとノリを合わせて、ABSのみこの品を使用しています。

K1MAXでABSをメインで出力していますが、いろいろ試した中では使い勝手が一番良いです・比較的均一に薄く塗り広げられる・ABS特有のソリにも耐えられる事が多い（完璧では無い）・水での洗い流しが簡単