StripMeister Original Drill-Powered Wire Stripper – Wire Sizes Up To Ø3/4", Jam-Free, Copper Wire, Built for Safety, Speed, and Efficiency - Portable Wire Stripping Machine

Once you get it set up for the size wire your stripping, works like a charm. Easy set up and faster and much much safer than using a razor knife. Good quality and well made. Should last a long while. We use a variable speed drill so you can go as fast or slow as you want. Made of thick aluminum except adjustment screws, cutter and feed wheels are Steele so it's light weight and can be mounted in multiple locations easily. Well worth the money, would purchase again.

Man I have been stripping wire for years by hand and THANK GOD someone told me about this it has saved me so much time and money i screwed it to a tabpe to make it more user friendly and you can adjust the blades to strip any gauge wire from 18g up to 4/0 with ease blade has stayed sharp thing is made well durable GREAT PURCHASE IF YOUR ON THE FENCE JUST BUY IT IT WILL PAY ITSELF OFF 1ST USE

This works amazing!!! I made a mistake and bought a Chinese version first, that didn't work at all. Then I bought this one. I was able to strip and clean over 200lbs, probably 2000-3000 ft of 6 AWG wire in about 30-45 minutes. It didn't jam or slip at all!!! This baby is amazing!!! Well worth the money

Well constructed solid piece of equipment, works as expected.

Great stripper, for wire up to 300

It worked great. Had some very hard coated wire and the Strip Meister made easy work of it.

Better than I expected. I love this thing. I have stripped all kinds and sizes of wire. From welding cable to 18awg fluorescent solid wire. It does it all. I was very reluctant to spend this much money. I considered all the cheap knockoffs on Amazon, but I decided to get the best. So glad I did.

I am an electrician specializing in remodel projects, so I am always pulling out old wire and recycling it. I have thought about getting a stripping machine for a while, but always thought I needed a big and expensive one. I finally broke down and thought I would give one of these smaller ones a try, and like others have said: why didn't I get one of these years ago?! It works well, and strips wire much faster than I could with a utility knife, and much safer, too. The unit is small, but that is a plus, not a minus. It is well built, with good milling of the solid aluminum frame and moving parts that fit tight but move easily. I bolted mine down to a small block of wood just big enough to hold it and the drill to run it. I can then clamp the unit to a work bench or stand, and easily store the assembly away when I am done with it. I will say that it can be a little finicky. Although the feed angle is not super-critical, it does matter for how well the material feeds through and, if set poorly, can cause the wire to slip to the side of the cutter wheel. Also, stripping smaller stranded wire (so far in the #14 - #12 range, I haven't tried others yet) requires much more accuracy with the cutting wheel, otherwise you end up with a lot of copper slivers as the wheel will cut the strands as well as the insulation. However, it doesn't take a lot to fine tune the adjustments, and once set, it runs really well. Therefore, any other reviewers stating they are having trouble with the wire not staying under the cutting wheel is simply not paying attention to their setup. Although I would not consider this is to be a production stripper, I have managed to strip thousands of feet of wire in just a couple of days. There are a couple of things this little stripper will struggle with, such as stripping the outer jacket of round multi-wire (aka 3-wire plus ground) cables, but again, with a little but of tweaking, it took me less than a minute to set up and strip over 100' of 12/3 that was probably made in the 70's or 80's, which has a much thicker jacket and a lot more paper filler inside, so it was quite a challenge. Once the inside wires were separated, I was able to just run individual wire after wire, and a couple of minutes later, I had several more pounds of bare copper in the pile. Overall, in a couple of days I will have finished what would have taken me weeks to do, plus I will get more money per pound for the stripped wire than if I didn't strip it, so this little unit has pretty much paid for itself in no time. If you are in the market for stripping a fair amount of wire, but not looking to make a living out of it (need a bigger machine for that), this little unit will certainly do the trick.

Fast and easy stripping, works brilliantly 😀

Absolutely brilliant. So easy to use. I was tempted to buy a much bigger electric stripper with multiple holes, thinking it would be a pain to adjust one like this constantly when changing cable sizes. After reading some reviews I decided to buy this, and I’m so glad I did. setting it up for different cable sizes takes seconds. It’s clearly made to a very high standard. I’ve successfully stripped the sheath off 4.0, 6.0 and 10mm twin and earth. It would easily do the smaller sizes as well if you can be bothered. Stripping singles I’ve done all types from 1.5mm up to 25mm. All have been super quick and easy. It’s already paid for itself, and will continue to earn me extra money for years to come.

Little work horse, works as stated. Save your fingers and hands and let the mechanism do it’s job. If it binds up use less pressure, as for larger cables run them through twice and the coating comes right off. Works fantastic with RW90.

I really like the performance of the machine, it does hours work in minutes and minutes work in seconds. It completes its targets perfectly. I am very happy with this machine.

Kvalitet + funktion 👍