Brampton Premium Golf Grip Tape - 2" x 10" Solvent Activated Adhesive Strips for Golf Club Regripping

No problems with this product. Easy to install the grip. Very satisfied.

They work and have easy to remove backing paper. I use them with the Brampton solvent.

good thickness and quality tape, works well with brampton solvent, relatively easy to peel off when regripping. use mineral spirits to clean off the shaft before putting the tape on, even trace amounts of grip solvent prevented good adhesion of the tape. the brampton tape/solvent combo doesnt seem to dry out as fast as other grip solvents, might need to extra dry time, but once dry its secure and holds up well. i prefer brampton products to other brands, its easier to work with, the tape is good, and the solvent doesnt make my skin dry out and crack

This tape is the best regripping tape out there. The quality is phenomenal, you can really see the difference between this tape and say one of those cheap pieces you get sometimes for free with grips or the double sided hook razor. They stick great to the clubs and are easy to put on. I regripped an entire set with these this week and they were perfect to work with. I ordered even more to have on hand. If you want to regrip your own clubs, get this tape, its simply the best.

Great product. I have ordered it before.

I've re-gripped 16 clubs so far at home. These grip strips are key. They work great combined with the HF-100 grip solution. What I do is remove the backing from one side and lightly stick the strips onto the bottom of the cleaned off shaft in an offset fashion, with 1/3 right of shaft and 2/3rds left of shaft, and leaving 1/4 inch beyond the end of the shaft so it can be folded in to cover the top edge of shaft after it's fully wrapped around. I press down the 1/3 side using thumb and index finger to smooth and tamp down bubbles or slight ridges so the 1/3rd side is adhering to the shaft just fine. Then I press down the 2/3rds remaining, smoothing as you go. Since the shaft tapers, the tape can overlap a little over narrow areas and not quite touch in a wider shaft area, it's not a problem. When the 2/3rds is 80% pressed down, peel back the 1/3rd strip backing a bit so you can finish pressing down the 2/3rds over the edge of the 1/3rd and make 'em stick together. Remove the backing completely. A few small ridges can develop because of the shaft taper, just tamp it down and don't worry about it using the non-sticky side of the backing paper. Fold the 1/4 inch at the end over the shaft end. Spray the HF-100 grip solution so the grip tape is wet end-to-end and all around. Spray 6 or 7 times inside the grip itself and slip it over the shaft end over the grip tape and slide it down. Too much spray is much better than too little. With 4 or 5 sprays, my grips became difficult to move down the shaft at about the 1/2 way point ... 2 or 3 more sprays makes a big difference in getting them on more easily. If your grips have a visual aid in the grip for helping square the clubhead, be sure to take this into account. I grab the club, point the clubhead up at 12 o'clock, wrestle the grip on, then rotate the grip so the visual aids are lined up with the squared head. This can take 2 or 3 adjustments until you like the look when grounding the club and seeing how you like the look of it. I do not have a vice on a bench, so I used the rubber vice grip that I originally got with 1st batch of grip strips and spray as a kit ... sometimes it's easier to just grab shaft with bare hand and bear down to slide the grip on. This is one reason I say more spray is better than too little! This is a long post for a simple product ... mainly to convey what you can do as an amateur without special tools. It's easy after you do a few and realize these little things to keep in mind. Lastly, the 'hook' blades recommended to cut off the original grips ... get 'em. I bought a 5-pack for my utility knife and they are perfect for removing old grips quickly, easily, and relatively safely. Having used them, I do NOT recommend using a normal knife or razor knife ... not worth the risk. It's fun to bring a stale set of irons or other clubs back to life with new grips, huge difference!

I’ve used these specific ones having gripped many different clubs and these by far are the easiest to use with their unique style of being split. You can’t go wrong with them.

This is the best solution for grip tape I have ever used. Just makes it SO easy to complete the grip installation in just a couple minutes really. The pre-split upper tape is the real game-changer, as it allows very quick removal compared to the old-fashioned tape. The length of the tapes is perfect for normal grips and you don't need to measure anything, just hold one end a little bit of the end of the shaft, pull the other end down parallel and then smooth out the tape one side to the other! Really great solution here!

Easy to use and fast to use for regripping. The exact right size and stick very good. If in a hurry and only need a small amount of tape these are excellent. Highly recommend.

This tape is easy to use and holds well. I would buy again.

Para cambiar Grip a unos palos antiguos pero en buen estado.

Can’t complain

Muy buen producto