Araldite ARA-400003 Standard Syringe Epoxy, 24 ml

Great Glue and value for money - Bought this to stick a variety of internal and external jobs around the house. Easy to use and mix with the automated dispenser. Never been let down by this glue - sometime super glue just doesn’t cut it and this stuff always delivers

does the jobs aridite does found it a little pricey Applicator nozzle long, ideal for safe application and accuracy

It's been my go-to epoxy for many years, it works perfectly every time and I can absolutely depend on it. It doesn't set quickly, so that makes it really good because it's not a race against time to get the glue where you need it before it goes off, or, to remove glue where its ended up in exactly the place that you definitely didn't;t need it! The syringe dispenser makes it really easy to use, when I first used araldite it was in separate tubes, which is ok, but it's far more messy and you have to ensure you dispense the same proportion of both parts, it comes with a stick to mix it, but I just use tea/coffee stirrers, you only need to mix it for 30 seconds and you can tell when it's mixed when you cannot see any streaks in the resin. I use my stirrer to apply the glue, in my pictures I filled a void in a 3D printed part, although the epoxy is quite a "stiff" glue, it will fill gaps as it levels itself, this allowed the epoxy to fill around my "joint" piece which connected both haves, I placed my part face down on glossy card. You need to clamp your pieces to hold everything in place while it sets, you definitely don't want it setting with pieces in the wrong place because they're not coming apart ever, I use some cheap clamps and they work great. You can see on the front that the epoxy levelled and filled in the tiny gaps, resulting in everything being bonded incredibly well, you would break the bits that weren't glued before you had anywhere near any issue with the glued section. I left it clamped for 8 hours, after which I removed the clamps and then let it sit overnight, the following morning it lifted straight from the glossy paper and revealed a very clean joint. As this part is going to be painted, I used a coarse grit sandpaper to gently and methodically work over the surface until it was level with the printed parts, at that point I worked up in various grits to 3000, after which the area where the joint and glue was smooth and flat and you are unable to feel any difference in the surface between the printed parts and this joint section, it's completely merged into the whole part. It really is one of the best glues around.

Difficult to beat it for some jobs, it’s been around for years and still comes out tops, the quick set version still gives time for adjustment. Wear plastic gloves!

Fussy and takes some pushing.

You can store for ages and it doesn't go hard in the tubes ,it takes a while to set but I think there is also a fast set version.

Used to fix the handle of a clay pot back on, left for 12 hours and seems to have help well. Main issue is it comes with only 2 applicator nozzles which only allow for a single use as the epoxy dries inside the applicator.

Does the job well

Toujours une qualité irréprochable une colle qui résiste à énormément de situation, utilisée depuis plusieurs années et toujours autant satisfait de ce produit

J'ai recollé un vieux pot en terre cuite pour l'extérieur et cela tient très bien malgré le poids. Il faut juste appuyer à s'en faire mal aux doigts pour faire sortir les deux produits.

Cher mais de loin produit ultra efficace

Bricolages divers - je connais ce prd depuis des années.

La qualité araldite est toujours là . Dommage que cette colle soit difficile à trouver. a noter que les délais de livraison sont très long ( plus de 15 jours) et que les informations de suivi presque inexistantes. Le vendeur vous répond mais pour vous informer que le produit est en cours d'acheminement et qu'il faut attendre la date de livraison annoncée.