Philips myGarden Arbour LED Outdoor Wall Light with Motion Sensor [Anthracite] 1 x 6 W Integrated LED Light, for Garden and Patio Lighting

Got this light when on offer at Amazon for £42 earlier this week. It will match the 3 Arbour (non PIR) lights I purchased last week. All 4 lights were to replace old rusting wall lights around the house. Installation was easy. Each installation took no more than 30 mins from starting to remove the old lights to the new Arbour light being ready to use. To be honest it was probably only 1 hours work to install the first 3 and 25mins for this PIR light as it was in a slightly more difficult place. First drill 4 pilot holes in the plastic wall plate and then use these pilot holes to mark the position of the holes you need to drill in the brickwork. I also used a small spirit level to ensure these markers would allow the light to be istalled upright! The Anthracite is virtually black and with our black woodwork it does not look out of place. Don't be put off by the lightweight feel of these lights. They look really good and are quite discrete too. Originally we bought cheaper lights at DunElm - as the saying goes 'what a mistaker to make'! - they were a nightmare to put up and once up two didnt work, so they were all returned for a refund. These Philips light look great and if you can get the non PIR for the low £30s and the PIR for the low £40s I can thoroughly recommend them.

As expected from Philips Lighting Well made Bright and easily adjustable duration timer and lumen settings Easy to fit and outdoor proof Happy to recommend

Bought this item in March. It worked for 2 months then completely failed to operate except to stay on all the time. The sensor was clearly not working. Only option was to turn it off at the mains which meant going into the garage to turn it back on manually, which defeats the whole object and meant a walk across my courtyard in the dark.

Looks great and easy to fit. The bulb is unfortunately non-replacable though which is a shame but as it's high quality LEDs they should last many years. My only issue is there is no way to adjust range sensitivity. I've had to stick some black tape over the top half of the PIR just so it doesn't light up when a cat runs across the road 3 miles away (that may be an exaggeration). Unless you are placing it facing a wall or an big area that will only get movement when someone is coming to the door it's lighting up, it'll be too much.

These were bought to replace some of the same. The grey outer cover is peeling but they have lasted 8 years. Of the 3 I have, one stopped working and was quickly replaced without drama by Phillips who were excellent. I could just swap over the covers as the internals and sensors still work as new. Easy to recommend.

A beautiful contemporary looking light from a reliable manufacturer. The light is super easy to install (I’m no electrician). The light output is bright but not overwhelming; it’s a warm and welcoming glow. The sensor is sensitive and captures movement well (easy to adjust and tweak). Price vs. Value is questionable; it’s a pretty basic light however it looks great so no complaints.

Let's get the negative out of the way first. So this light does not have the functionality of a manual overide. What I mean by that is the ability to overide the PIR and set the light to remain on permanently. Most PIR lights have this feature which is enabled by flicking the light switch on and off, the Philips however does not. Had I known this I would not have purchased. On the positive side, the style of the unit is pleasing and the PIR sensor works very well. The light spectrum is a warm white and bright enough to light the front of the house without being intrusive to the neighbours.

Before drilling any mounting holes, ensure that there is enough cable to enable the light to be situated where you want it and the power is off I.e if the cable is not long enough it will make fitting/wiring the light difficult, and you may end up compromising where you want the light. Next ensure that the light is level and drill 1 of the top holes using the removable back plate (lighting unit)as your template. Fix the back plate (lighting unit)with a wallplug and screw into the hole that you have just drilled. NB Ensure that you have threaded the cable from the wall through the supplied grommet and you are able to connect the wires to the appropriate terminals inside the back plate/lighting unit. After you are satisfied that the back plate (lighting unit)is level, drill another hole in the bottom opposite corner of the first hole that you have drilled and insert another wallplug and screw. Once you are completely happy drill the last 2 holes and insert the wallplugs and screws. Finally connect the wires from the wall cable to the terminal block inside the light unit (these are clearly marked) and fix the light unit cover to the back plate All screws and wall plugs are supplied with this light. Next switch the power on. Worth noting that it is much easier to set the sensitivity, dawn/dusk and timer when daylight is fading. Just to clarify that the back plate/lighting unit are the same thing .

Buena calidad siendo reciclado

Très beau rendu s’intègre parfaitement dans son emplacement . Bon produit Merci pour la livraison rapide

Modern und günstig.

Parfait

Mooie energiezuinige moderne lamp. In te stellen voor detectie licht/donker en de tijd (hoe lang de lamp aan blijft als er geen detectie meer wordt waargenomen). De lamp is niet goedkoop maar bij aankoop gedurende een aanbieding is hij betaalbaar. De tijd is een beetje moeilijk te doseren maar ja het komt niet op een seconden.