Curt Manufacturing 13367 Class III Receiver

Great value for the money it fit perfectly with no drilling or welding needed. It shows a receiver attachment with a ball in the picture of a video, but that is not included, but the hitch itself has got great hardware all included fit function or excellent.

I installed this on a 2007 Toyota FJ Cruiser. It is pretty much a 'bolt on' process; I was able to do it solo without too much trouble (if you can hold up 25-30 lbs with one arm, you'll be able to do the same). My biggest problem was getting the factory tow 'loop' off. The only tricky part of the install is the step that requires you to wire-fish two 7/16 carriage bolts through a square spacer. Your mileage may vary, but I found that the fish-wire method was actually more difficult than simply using a magnet to pull the bolt through. Unless you have very thick fingers, you shouldn't have any problem getting the square spacer into place. Rare-earth magnets (like you can commonly get in stores now for super-strong fridge magnets) work very well for this. The one bolt I tried to do their way slipped out and I had a bit of fun locating it and bringing it back to where I could grab it. The one I did 'wrong' was a piece of cake.. That said, the above fish-wire part may not apply to your vehicle. This being my first hitch install, I have no idea how common it is. But that last bit says it all.. This was my first ever hitch install and I had the thing on by myself in less than an hour. Two days later it proved its mettle, hooked to a tow-strap/airplane towing cable combination as it pulled over a shed.. No problems at all. I do recommend a hitch cover though as the mount sticks out further than I expected on my vehicle and one could easily bang their shin/knee into it..

OK, first this thing is a tank and fit my 2011 FJ Crusier perfectly. In case it's not clear this is designed exclusively for the FJ. You can check it out on Curt's site. OK, now for my tips on install. I understand why the other reviews highlighted the tow hook removal but if you just know you'll need a breaker bar going into it then it's really not hard at all. If you don't have one someone you know will because it's a fairly common tool. So for me the hardest parts were removing the exhaust hanger from the dual rods. The instructions weren't helpful in that regard. I sprayed the rods/rubber hanger with PAM (don't get on exhaust pipe) and then just pulled it off with considerable effort by hand. I'm stubborn and inpatient so rather than wait for a friend to help hold the receiver up I had to balance/lift the whole thing myself to get the first side loosely bolted in which was very tough but doable (i'm 6'4'' 200lbs). If you're not OCD get a buddy to crawl under to help you. Other than that it was pretty simple. I could not be more happy with the receiver.

Bought this for my 2007 FJ cruiser. the fit and quality is perfect. installation CAN be done with one person but a sencond person might have made it a bit easier. All the hardware needed is included with this kit and there is no modification needed to the vehicle aside from removing the factory receiver.

high quality easy install.

Good and sturdy receiver, however did not quite match up with the existing pre drilled factory frame holes and I had to spread it with a bottle Jack to get it to match up. Otherwise this would be a 5 star rating.

Put this on myself on a 2010 Toyota FJ. Takes longer than the estimate if you dont have air tools (which I do but didnt want to drag all that stuff out). Took about an hour. Very well made hitch, and Amazon was lots cheaper than everwhere else including ebay. The FJ tow loop was a hag, had to use a 2 foot long half inch ratchet and yank a few times. Looks much better than the toyota factory hitches. Very manly. Didnt need the fish wire for anything. Would highly reccomend this hitch. Made in USA, YAY.

Box is heavily damaged when arrived but probably expected for the wait and size. Quality products but to me it look like it was probably used because of how banged up it was. The driver side back to holes did not fit by a quarter inch had to pull off redrill and ream. 100%, the whole pattern was just off unfortunately. Probably one of those things that happens I didn't send it back I just modified it and made it work. It does come with the mounting hardware and the fish Hook.

It seems well made, solid product. Time will tell. I recommend to go to install in a workshop, on the lift and proper tools takes 20-30min to install. Doing it at home you need to be 2 people as this piece is very heavy to handle. Be aware that the exhaust tip my touch a bit the hitch, so need to be adjusted properly when you install it.

Great Price, Awesome Product, Super Fast Delivery...