Mount-It! Bookshelf Speaker Wall Mount, Pair of Universal Side Clamping Speaker Shelf Wall Mounting Brackets for Large or Small Speakers, 2 Full Motion Mounts, 55 Lbs Capacity, Black (MI-SB37)

I bought these to wall mount my kanto tuk speakers I use with my pc. I wanted to free up room on my desk and these were the perfect solution 👌. Heavy duty and very easy to mount, even comes with all the necessary hardware as well!! The cover slides over the base and provides a clean look. These can swivel side to side and forward and back as well, very nice feature. The base can adjust quite wide and provides a nice tight fit so ur speakers will stay put. They even have holes that u can use to screw them to your speakers and included screws for doing so. I didn't want to drill holes in my expensive speakers so I just tightened the clamps and they are very snug and not going anywhere, these are very easy to adjust. Overall, I really like these mounts and would reccomend them to anyone looking for a very reasonably priced speaker wall mounts.

Excellent wall mounts! Heavy duty little puppies so be wise about how and where mount them.I used larger wall mount anchors to be safe. Glad I have a 3/4 inch wood paneled wall.Toss in speaker weight. But they came on time. Very well built. Fit bookshelf Klipsch I planned perfectly with room to spare for a larger set. They aslo grip very snugly and have pads to protect the surfaces of the speakers where it makes contqct with the speakers. Id so buy another set of these of ever needed them again. Hope they keep producing these. Plan to install more in the future in other rooms.

I bought these mounts for use with some small Polk bookshelf speakers. The mounts themselves are extremely well made and sturdy, I have no doubt that they'll hold the weight they claim. They were easy to mount into drywall, and came with all the necessary hardware. It took me about an hour to do the measuring and installation. The included instructions were very clear and easy to read, and the actual mounts themselves are simple to put together. You might want to have another person around to help you, it's handy to have someone else hold the mounts in place while you insert the screws into the wall (but if you're careful you could do it alone). You don't have to screw into your speakers, the mounts themselves have nice padding on the speaker bracket, so they hold speakers in place well. They do give you a bit of angle and side to side adjustment which is nice. I do wish they could angle down a little more (I have mine pretty high up on the wall, it would be nice if I could point them down a bit more). But Mount-It's advertising and product info was accurate so I can't blame them for that. Overall for the money these are great. Very sturdy and I do recommend them if you are looking for simple, clean looking wall mounts that give you some adjustment as to where your speakers are pointed.

Use Case I got these wall mounts to have a cheap way to use some old JBL S26 speakers in my garage. I needed a mount that could handle the weight, could angle the speakers somewhat downward, was inexpensive, and wasn't too unattractive. Packaging/Build Quality/Appearance The mounts arrived in a small white box. The finish of the mounting arms is protected with some cardboard, and everything is bagged. The hardware is in a single bag, with different parts sealed into different compartments (my least favorite packaging method). The welds of the square tubing to the flange were clean enough (though you won't see it if you use the cover plate), and none of the pieces appeared to have any surface finish imperfections or structural issues. The item looks fine... it's not an eyesore, but it's also not attractive. The finish on the metal is nice enough, but the plastic of the valence and end cap don't match it. The offset portions of the speaker clamp mechanism are not particularly nice to look at (when viewed from the bottom). Installation/Assembly (see special note!) I opted to mount my speakers into my wall studs. The JBL S26s are about 24 pounds (each), and with as far out as I was putting them, I didn't really want to trust wall anchors in sheetrock. If that's the route you're going to go, I would really consider buying better piton-style anchors to use instead. With two screws securing each mount plate there's enough play to get the mount level. Once the arm is mounted, you slide the cover over the assembly, and place the cap on the end of the arm. The bolt/cap assembly has a single nut responsible for securing the tilt/swivel position of the speaker - the problem with this is that there are no lock washers provided, and the bolt is not slotted, nor does it have a hex head. While you can certainly use the hardware provided, I definitely would recommend using a lock washer instead of the flat washer. I used them with the nut (because I didn't care how it looked - silver vs. black), but you can use them at the bolt if you care more about the finished aesthetics. The clamping mechanism seems solid enough, but I didn't trust it enough to use it without the accompanying screws THAT GO INTO THE SIDES OF YOUR SPEAKERS. Since I don't really care about my speakers, it wasn't a big deal... you may feel differently about damaging the finish of your speakers. The clamping force may be enough by itself, but I didn't really want to count on it, since I have the mount at the largest downward angle you can set... the last thing I need is a speaker bouncing off of one of the cars. Conclusion If I had known that speaker stands like this were this inexpensive, I would have gotten them years ago. Sure, it would be nice if lock washers were included, or if there was a cap to put over the adjusting nut, but what can you really expect at this price point? Definitely recommended.

High quality, heavy-duty speaker mounts. Having tried other types, I am very happy with these. I have some useful tips for mounting them that not in the instructions. Other than these omissions, the instructions are good. Measure your speakers before ordering. The description says the speaker mount kind is good for speakers 5.38 to 11.13" wide and up to 55 lbs. My speakers are 7.25" wide, 10" deep, 13 lbs; the mounts work well. Deeper speakers may have rotation limited by their rear corners hitting the wall. In that case you can use a block of wood to extend the distance from the wall. I did not need to do that. The mounts MUST be securely fastened to walls or the speakers and brackets may come down. If you have plaster walls, use a stud finder to find the center of the wood stud and drill a 3/16" pilot hole in the center of the stud for the provided screws. If you have steel studs, get suitable screws at the hardware store. If you have brick or concrete walls, use the four provided anchors with the screws. Do not attempt to mount on plaster alone. Anchors in plaster may not be enough. There's a review here where the person complained that they put the brackets on the wall but they came right down when they put the speaker on the stand. That's a problem with the wall fasteners, not the bracket. If you don't know how to do this, find a handythem. Suppose you want to place the speakers such that the tweeters point to the ears in the main listening position. Have a friend measure the distance from floor to your ear with a measuring tape. It will likely be 36-45"; for me and our couch, 42". Measure the distance from the base of the speaker to the center of the tweeter. For my speaker it was 12". The distance from the center of the top mounting hole to the platform on the assembled bracket was 1 1/8". The distance to the center of the screw hole from the floor, for my case, is 42" - 12" + 1 1/8" Studs may not be where you want them to be. On one side, I had 16" from corner to center of the stud. On the other, 12". This difference does not matter if you complete the job by rotating and tilting the speaker so that it points to the center of the ear. An easy way to do that is to tape a laser pointer on top of the speaker, turn it on, and adjust the speaker to point at an ear. Since I was working alone, I used a styrofoam wig stand as the target.

I am very happy with these mounts. I would absolutely buy them again. My front speakers weigh 29 lbs each, and they are not going ANYWHERE! They look fantastic, solid build, the swivel system is easy to position, and the clamps on the side do a great job keeping my speakers in place. The clamps are padded so there is no worry of scratches. I used some 5/16 x 2 inch lag bolts to screw these bad boys into my studs and used the provided anchors where needed to keep them from vibrating. There are only 2 negatives that are not really a big deal. 1) I would not recommend someone only using the provided screws to mount these, it will probably work but would make me uncomfortable. Do yourself a favor and buy 4 of the lag bolts I mentioned earlier and get at least 2 on a stud for each mount. 2) The plastic cover on the back is not exactly heavy duty, just be gentle with it as one of mine cracked while we were installing them. Just be careful with them and DO NOT put the plastic covers on before you screw the base onto the wall. I know it sounds silly but if you put the plastic cover on before you mount the base to the wall the plastic covers will get snagged on a screw on the back. You should really consider these as they were inexpensive, easy to install, look great, and will keep your speakers safe.

Figured it was high time I upgraded the Front Height Atmos speakers in my theater. Wanted to stay within brand for timbre match and finally decided that a pair of Definitive Technology Studio Monitor 450's was the way to go. But damn, they're big (14x9x12) and pretty heavy (22lbs) to mount on a wall. Stumbled across these and missing some of the (misguided) put reviews, decided to give em a whirl. Wow! Surprised. Really well made. Strong and relatively easy to mount. Wasn't crazy about inserting a retaining screw into speaker base, but... Not only holds speakers securely but pivot mechanism allows for precise speaker alignment position, even with fronts pointed down! Was little worried about visions causing mount to loosen (have four truly monstrous subs in room) but nope, no effect at all. Big recommend! Great product!

After ready many reviews, I decided to go with these and was not disappointed! These wall mounts hold my Sony SS-CS5 bookshelf speakers just fine. These were easy to mount onto the wall. If you have a stud, they can mount with just 2 screws. If not, you can use 4 screws and anchors. These mounted in wood paneling, and I used anchors. Sheetrock might be the same, just make sure you get some good anchors and use all 4 screws. These mounts adjust so I could mount them on the side walls and then turn the speakers to face where we sit, as these are my front surround sound L and R speakers. Adjusting the brackets to the width of the speaker was easy and I was able to tighten these without any damage to the speaker housing. Some people mention using an adhesive rubber strip to help with gripping the speaker; however, I felt the brackets held the speakers just fine without the need for anything extra. Although it's not major, I wish the tilt angle was a bit larger. since I had to mount these fairly high, I would have liked to have had them tilt a little more. Again, no huge deal. Overall, I am very pleased with these mounts. They mount securely and hold these larger bookshelf speakers just fine.

Solid speaker mounts. I was concerned they might not be strong enough to hold my Klipsch Sevens at around 10kg each. They hold them no problems, are sturdy and look neat and concealed. Plastic cover over the mount is flimsy but doesn't affect the product. I haven't drilled into the speaker sides to hold them in place, may make a mounting bracket at some point but they balance nicely and the side clamps hold them in place. Overall happy with them but wanted to let other owners of Klipsch sevens or similar know they are suitable.

These work great to mount my Yorkville YSM8 Monitors above my desk. Very sturdy and easy to install.

Good quality, strong and sturdy perfect for the job! 100% recommended.

Son funcionales

Very happy with the build quality, strength and price of these mounts. Would buy them again!