BN-LINK Digital Cooling Thermostat Controller, Temperature Controlled Outlet for Attic Fan, Exhaust Fan, Cooling Devices 40-108°F, 8.3A 1000W

This is a very well built product! And this is just what I needed and it’s so easy to set up and use. Now when my shed gets up to the temperature I set this will activate a fan plugged into it. When set up it displays the ambient temperature. When that equals or exceeds the temperature you salet, it activates whatever is plugged into it. In my case it’s a fan. Highly recommended.

Works well for a few days now, kicks on at the set temp. It’s been reliable so far. Installation was simple—there’s a keyhole slot on the back to hang it on a screw. My only complaint is that it has just one mounting slot at the top, so the bottom isn’t fully secured. It includes a wired temperature probe, allowing flexible placement. I kept mine near the unit, and it reads accurately. The digital display is bright and easy to read, even from across the room at night. Programming is straightforward: hold the “Set” button, then adjust with the up/down arrows. Pros: Compact, accurate, bright display, easy setup Cons: Only one mounting slot; temperature adjustment requires holding “Set” first. So far, so good, happy and hope it holds up long term.

Cooling thermostat works really well!! I’ve got it hooked up an exhaust fan in my greenhouse and have it set to come on at whatever temperature I want and it does the job really well.

This turned out to be a pretty cool little controller for my shed fan. I have been using it for about a month now. Been working perfectly. I have the temp set to 85 F in my shed. Kicks on every time when passing that mark. I have it powering my 10 in. shutter fan. Installing it was pretty straight forward. It has a slot on the back to allow you to slide over a screw. So, you would pick your spot and put screw for it to hang off. My only gripe here is that it only has one slot on the top back. Which leads to the unit not as secure at the bottom. It also comes with a temperature probe. The probe has an attached cord that allows you to place the temperate probe away from unit. I ended up just leaving my in a coil and close to unit. Seems to be reading temp just fine. But, this does allows you to place it closer to where you might want to measure your temp. The digital display on the unit is nice and bright. I can read it from across my shed and in the dark. The controls are easy to use. Adjustments are fairly simple. Simply hold down the "Set" button on the unit and you get in setting the target mode adjustment. Then you use the up and down buttons to set target temperature. Pretty easy. Pros: * Compact * Accurate Temperature * Bright Display (Red Digital Numbers) * Easy setup and programming Cons: * Needs a bottom screw slot for secure bottom of unit * Although it's simply to adjust the temp, it can be even better if the up and down buttons just let the adjust temperature target directly. Instead of having to hold down the set button. Overall I'm happy with the unit. Hopefully it lasts.

We've got a 200 bottle wine cooler. It's suppose to be the best available. Unfortunately, who ever designed it didn't consider how it might be installed with very little airflow to vent the cooling coils. After three years the compressor gave up. The repair guy told me that unless some positive airflow was added we could expect to replace the compressor every three years. I added two low speed muffin fans but there was no way to connect them to the cooler so they would switch on when the compressor ran. I nosed around Amazon and found the BN-LINK Digital Cooling Thermostat Controller. At nineteen bucks it was a cheap device to try out. I got the fans installed and hooked up the BN-LINK. Plugged it in and watched it come on line. It displayed the ambient temp. It took about five seconds to set the trigger temp. Aimed a heat gun at the temp probe and watched the display show the temp increasing. As soon as the target temp was reached the fans started spinning. This is a great little device. Simple to install and program. The only suggestion I'd make is provide a little more space between the power outlet and the temp probe cable.

Works great controlling my exhaust fan

Per the spec sheet that arrives with this BN-LINK temperature controller, this unit can only handle 4 Amps for INDUCTIVE loads, such as fan motors! The description on this product falsely claims that it can handle 8.3 Amps for circulation box fans, but ALL electrical motors are INDUCTIVE loads! My 18 inch attic exhaust fan uses 5.6 amps, and thus I could not use a device rated for 4 amps to run a motor using 5.6 amps. I reviewed ALL of the reviews before I purchased this product, and wondered why many users complained that this product failed after using it for a year. If the reviewers used these controllers on fan motors that require more than four amps, it is a wonder that the controllers lasted for a year! - Amazon, please update this product listing to state that while this product can handle 8.3 Amps of RESISTIVE loads, such as lighting and heating, it can only handle FOUR Amps for INDUCTIVE loads, such as fan motors. The product does seem to be quite accurate, insofar as temperature control, but I could not use it for the attic fan motor that I had purchased it for.

this thing works awesome . just plug it in hold the up button for 3 seconds for Fahrenheit ,hold the down button for 3 seconds if you want Celsius, hold the yellow button for 3 seconds to set the time up or down.. hit the yellow button again and it set put the probe wherever you want the temperature to be adjusted ...I drilled a hole in the side of my solar panel this unit is not waterproof so if you use it out door like I am make sure it's protected and so is the probe... I'm using it as a thermal on off switch for my solar pool water heater I made a solar panel with 50 ft copper tubing inside glass encased [2 of them ] I wanted to have this turn on a sump pump sitting in the pool 18 inches below surface..I wanted this to come on when the solar panel got hot 100f... not on a timer because some days gets rainy... I have it hooked up to this sump pump... that pushes water to solar panels that are 6 feet below the pool surface ....15 ft away from the pool 100 feet of half inch outer diameter copper tubing works great... https://www.amazon.com/your-orders/pop/ref=oh_aui_i_d_old_o6?_encoding=UTF8&gen=canonical&lineItemId=kgjirqlpkjsrsny&orderId=112-8601220-8637060&packageId=1&returnSummaryId=&returnUnitIndices=&shipmentId=DZ6wthHSb It is a 52 inch high 12 foot by 24 foot Intex swimming pool the sump pump is 18 in below water surface With 2. 24 inch by 5 foot glass pane solar panels ...each 50 foot copper tubing inside it is able to raise the pool temperature approximately 10 degrees I'm at 60 gallons per hour As in water coming from pool is 70° going back in pool at 80-95f Over 6 hours it raises the entire pool somewhere between 1 and 3 degrees more then just the sun itself per day The pool is 8600 gal so the entire pool os turned over in 14 days 10 f warmer then just Sun itself Works especially good at the beginning and end of season to extend your pool use

Me equivoque yo ocupaba el modelo que es para calentar

The only thing keeping me from giving this a 5-star review is the lack of functionality to widen the temperature range between on/off. We're using it to control a box fan near a wood stove and initially I noticed that when the fan would kick on it was able to remove enough heat from the area to cause the thermostat to shut the fan off - once it reaches the set temperature and turns the fan on, if the temperature drops only 2-3 degrees that will be enough to trigger the thermostat to shut off the fan. The solution to this was pretty simple - just a relocation of the temperature probe closer to the wood stove and an adjustment in temperature setting to compensate for it. However, it did take me quite a while to find just the right location to place the temperature probe in order for it work the way I'd like, and I think the whole issue could be avoided if you were able to adjust this on/off range to be a little wider. Overall it's a great product. It's been working fine for the 5 months we've had it and we run this stove all day and night, every single day. Works great.

Hoy es el primer dia que lo probé, no lo ocupe ni 1 hora y de repente me di cuenta que estaba dando energia a pesar de que estaba apagado el foco que dice “cooling” este apagado o no, no funciona el termostato, al principio si funciono, me fui a hacer otras cosas y a la hora ya no servia, es una basura. Como ven se encuentra conectado a una televisión para que se pueda ver el funcionamiento y como la television permanece encendida, este apagado o no el termostato y el foco que dice cooling, al principio cuando se apagaba el foco cooling se apagaba el aparato que tenia conectado y al encenderse encendia, despues de un rato dejo de funcionar y lo probe antes de conectar un aparato de refrigeracion Justamente por eso lo compre, para conectar un aparato de refrigeracion para cerveza pero antes de usarlo decidi probarlo para que no me fuera a dañar la cerveza, como ven, no duro nada, si lo hubiera conectado a mi refrigeracion seguramente se hubiera dañado la calidad de la cerveza, no lo compren, cambiare mi review en cuanto me devuelvan mi dinero Es un poco molesto porque justamente hay que detenerse en los procesos debido a que los productos que se compran luego no son de buena calidad, esperaba que minimo me funcionara 6 meses :(

I purchased this digital thermostat for my kegerator, and it has been a game-changer! My keg fridge is built into the counter, making it difficult to reach the control dial on the back. This thermostat allows me to control the fridge temperature to very specific settings in an accessible way. The setup was straightforward, and it has worked flawlessly since I bought it over a year ago. I can easily manage the temperature, ensuring my beverages are always at the perfect chill. Overall, I highly recommend this digital thermostat for anyone needing precise and convenient temperature control for their kegerator or fridge.

I like the design of this. The features are pretty good, except would be nice to be asble to set the temp in 0.5 increments not just full degrees. Reason i state that is then it would be able to have a narrower " action window" between on and off. Now as for the one i received, i have done a side by side temperature check with a known / calibrated thermal probe and i find this unit reads most of the time about 2 degrees C to the high side. That could be easily taken into consideration when setting the temperature. HOWEVER i have also found this to have an error of as much as 1.5C lower than actual to as high as 5C above actual over its adjustment range.... i suspect they have a poor calibration curve in the firmware for the probe used. OR Maybe this is a bad one .... just not as good as people think they are ??? I tried to save a few bucks compared to Inkbird, but in reality for $10 more and having a unit that does cooling and heating in same device PLUS a calibration curve option, inkbird is the winner. this is just too over priced to have these problems .. returning