Ḅḷueṭooṭḥ Speaker

ASE Certified Master Technician with 30 years experience. This was a fun kit to make. Not too much soldering though. Easy soldering with nothing too small or difficult. Sounds good for what it is. Connects well every time. Instructions were incorrect on one step. The step to connect the light control to the power supply. I was able to connect it to the switched 5V power and ground circuit at the switch and it works perfect. The screws holding all the panels together were a challenge for my FAT FINGERS but I like a good challenge. My switch was too large and too stiff and cracked the panel when I tried to install. I would heat it up a little to make it pliable or trim the tabs off next time. I liked this so much I ordered another one for my wife. Hers was missing a couple screws and they quickly replaced the missing parts with another kit. I was also able to replace my broken panel out of the replacement kit. This is a great beginner kit. This was her third kit to make and she loved it as well.

Good for the price, it sounds good, did some modification and put some vinyl on the casing, did put a battery to make it portable, retained the original plug for charging the battery and installed charging module for the battery. Looks cool and the quality of it is perfect would recommend this for beginners who wants to learn how to solder and enhance soldering skills to take it further. very satisfied with this product. Very easy to assemble, The size of it is cute size but hase a powerul sound.

First things first: Pay attention to what you are ordering. There are two separate kits as the same product. The more expensive one has the large spectrum LED panel (and apparently requires some SMD soldering), while the less expensive has 11 multicolor LEDs and is all through-hole work. I opted for the less expensive kit as I don't see the benefit of having a bunch of lights on what is essentially the back of the unit. The soldering you'll be doing in this project are just the components on the small board at the bottom, as well as some wire connections. It's very good soldering practice for beginners and did not take an excessive amount of time to complete. The instructions are provided by a QR code link in the box. It would have been nice if they had also put the URL the QR code linked to on the sticker with the QR, for easier access from a desktop. THE HARD PART is putting the acrylic case together, especially if you've never put something like that together and are not familiar with working on acrylic. I can forgive the reviewers who claimed the case doesn't go together: It's not super-obvious how you're supposed to tackle it and they completely skip over how to do it in the instructions. This is one part of the project where they could really improve the experience by showing the best way to get it together. I got my case together without cracking anything, but it was a patience-testing experience as I slowly figured out how to do it. One thing i found helpful was to use a magnet against the side of the nuts as I slowly tightened the screws into place. This kept the nuts/screws from being sucked up to the speaker magnets. Be careful not to over-tighten the screws: you're either going to make them pop out of place, or you'll crack the acrylic! TIP: note that the top plate actually slots into the speaker plates, so it might be easier to start with that (instead of making the mistake I did and noticing that at the very end). Sound of the finished unit is decent for what it is. Good enough that I put it on one my computers to use as output when I want to show the kids something (I usually just use headphones). The lights on the unit are really cool - no complaints there... even if mine didn't have the big LED panel like the more expensive model. They are very animated and colorful. I haven't experimented with using cards or USB thumbdrives with it, but I've connected the bluetooth to both my Android phone and my Linux desktop computer with no issues whatsoever. The remote control also works as advertised.

First of all, there are 2 different types of this product, and they both ship with the same instruction sheet. I happened to have the product with different-colored capacitors, and the sheet didn't specify that there were 2 different types of the product until way later. That led to a lot of confusion. Second of all, the part of the project where you have to cut the white plastic tip of the red and black wires, which makes it impossible to solder if you mess up even once. Also, the project had a segment where you had to solder a wire mere millimeters from a rubber pole, so when I soldered the wire into the designated hole, I fried the rubber pole, which could be very toxic and dangerous. Don't buy this product.

Overall the experience is fine. It teaches what the main purpose is intended of soldering components to a board. The speaker quality is poor but, again not the purpose of the project. The case that the entire project is enclosed in is garbage and cracks easily. It is more trouble than what it’s worth to assemble the case as the hardware is so tiny and hard to handle. Instructions are clear and easy to understand.

Possibly the best 24 bucks I've ever spent. I built it in an evening, the hardest part is assembling the case, good soldering practice for anyone who has an idea of how to do it, complete noobs should watch some u tube vids before attempting it, the only problem I found was that the power switch would not fit into its hole, I used a nail file to lengthen the hole in a couple of minutes, the case will crack if abused. Once it's assembled it is quite sturdy and the sound quality and volume are great for the price, surprisingly loud, no real distortion at max volume, obviously not audiophile quality but I was impressed by the sound quality. The bluetooth is also very good, long range, easy connections. I like the lightshow, some people might be able to modify it to suit their taste. I'm thinking about putting a battery in it to make it more portable. If you think you want one buy it, you won't regret it.

Bought this for my son as he has been wanting to get more into electronics. And who can't use a little practice soldering? He said it was pretty simple to put together. Nothing was difficult. Normal soldering is about it. Instructions are good as well. Not going to say it has amazing sound, it is a inexpensive kit. But sure is a fun kit to put together. And it looks cool with the lights. Very happy with the kit, would gladly recommend.

For a beginner electronics project this is pretty cool. It’s great for working on those soldering skills and gives you some basic electronics teaching. My only real negative was the very this acrylic used for the structure and the tricky screw and nut assembly. A little bit thicker material would have been nice, it’s 1/16”, 1/8” would have been better. Once you master the screws it ended up being fairly sturdy….. a note to anyone buying this, the rectangular cut out for the switch is a bit too tight, mine cracked at one of the corners, use a nail file to open it up a pinch. The sound quality is pretty good and it makes a good little desktop speaker. Overall, not a bad purchase