Techna Clip Concealment System for SIG SAUER Pistols - Durable High-Carbon Spring Steel Gun Clip w/Teflon Coat 1500 - Easy-to-Install Gun Holster Clip (Black)

Great product easy to install took less than a minute clip is sturdy and keeps locked on belt through basically any task if your not very flexible it’s a pain to wear at the 5 o’clock position and it adds a bit to the grips which isn’t to bad unless you have a sharp corner on the grips then it leads to snagging nothing a file couldn’t fix it’s a great product and will be buying one for my other guns

I bought this clip and the product photos which depict the pistol sitting nearly out of view are NOT pictures of this clip. In fact, the clip edge is near the trigger, so about 1/3 of the pistol will stick out. Instead, see the additional "customer" images which I uploaded and you will see the difference. Otherwise, it does not interfere with the slide and works as intended. It is a very stiff clip which is nice, it assures the pistol will not slip out if you are moving around. It's there to stay. The only issue I have is that if you put it in the small of your back, right-handed draws are more difficult because the grip is now facing the center of your back. It's too bad this cannot be mounted on the other side of the gun. I use this frequently and would recommend it. NOTE: This works fine under the Hogue rubber grips, as it includes longer grip screws.

Im sure this is a great product if it works with your model. I hate my iwb holster. But the screws provided, which are longer than the factory screws, are still too short to install on my piece. They dont reach far enough to grab onto the threads and tighten down. And im not willing to sand or grind anything on my gun or grips down to try and "make it" work. So im just returning it. Again this is with the sig p938 Spartan model.

Edit: switched to Hogue grip, all pretty perfect. Just have to loctite bc the screws are just snug at max depth wo interfering with the mag. Awesome after 30mins of work. Worth it for ease of carry. Screws supplied are of good quality and the right thread pitch and length (for most). IT ALL DEPENDS ON YOUR grip's thickness. I was installing with factory rubber grips. The replacement screws were only picking up two full turns in the frame (likely to strip). I had to dremel out the grip by 2mm to allow the screws to fully seat into the frame. WATCH the inside of the mag well as you test screw depth while you take plastic off of the grip screw head cut outs bit by bit. Done slowly and carefully, I got the screws to seat deeper into the grip and fully tighten with only a mm of distance between the mag well level and end of the screw. Perfect. Lastly, the factory rubber grips are not flat-backed so there is a small gap in places, especially at the bottom front of the grip. The problem was helped by taking some of the bend out of the clip as it is too tight on the gun frame and torque causes excess pressure on the mounting areas. (Note: the picture makes it look like the clip comes off of a solid plate; however, it's not a plate. It loops around the frame cut outs like a C with a gap at the front of the "C"(another brand is shaped the same way and can be seen in their pics). The fit is not perfect. Not to my typical standards, but for a piece one fully intens to scar and use daily it works beautifully. With flat backed grips this will likely fit perfectly. Modification is def likely to get screw depth correct. Grips type will ultimately determine the fit and finish. Besides being a bit over bent and the clip being too firm, the product itself is GREAT. Screw length is right in the middle for diff grips... good screws... if the depth is too shallow, take grip material... if screw depth is too long and interferes with the magazine, grind the end of the screws. Go slowly and pay attention with taking material if necessary and the end result is... Freaking awesomeness for waist or pocket carry of your daily "work" piece!

This product works exactly as described / expected. As for the review with it rubbing the slide, I dont think they installed it correctly. I had to hold the clip in place while I tightened the screws, or it would have rubbed the slide. but it is spring steel, it has a push to it. Hold it in place while tightening, and it fits perfect. To be honest, I've not taken apart my sig yet, nor do I know how to for sure, but i cant see how this clip can make a difference in removing the slide. It doesnt cover anything. It does ride high compared to my kel tec .380 or how the ruger pictured with this product in the ad would - they both have the back of the clip mounted to the back of the gun by the hammer - Most of the gun is below your waste line. With this product, the part of the clip that hangs the gun to your pants stops at the front of the grip, so it rides higher, but at the same height most holsters would hold the gun. It is actually the best height, the whole grip of the gun sticks out of your pants for easy draw, unlke my kel-tec where you have to work to dig the grip of the gun out of your pants. I was worried about the gun being top heavy or falling out with it riding so high, but it is MORE stable and MORE comfortable than carrying the gun in my uncle mikes holster. This made my favorite carry pistol as comfortable to carry in my wasteband as my kel-tek (which carries great, but I dont trust my life to it). If your looking for the easiest / lightest / smallest / yet still very secure way to carry a good pocket pistol, this is it.

I I nstalled on my extreme, easy install and nice fit except slight gap between grip and frame. Carries nice, no bulk. Shooting after 50 rounds or so it dug into my hand where the gap is. I ended up removing it at the range. I like the idea, but after trying many holsters I like my cheap simple Uncke Mike's IWB. It is thin and gives me something between my skin and the gun. Difficult to reinsert but draw is all I care about. Also works well inside front pocket. I may put it back on for carry, does not interfere with my favorite holsters. Nice option. Works with CR laser guard.

call me odd but I like to know what I carry is close by as in skin yes I know thire are those who will say the only way to carry is with a holster or rig however having done all 3 I peffer this for SOB carry simple and effective pluse it stay,s put \ my only cavieat is that when you remove the slabside,s to install you will have to sand down the inside of the slab for the belt clip to fit right the inside of the slab handle has a bit of extra wood that interfere,s in instlation of the belt clip rember your working with aftermarket hear so be carefulll and sand down the slab flush so the belt clip will be secuer and allwas tighter up your screw,s right and tight

Purchased for my P365X. Wouldn’t fit in. I had to use a file and file the edges down some in order for it to fit. Once I got it installed, it worked fine. I carried with it a few days and didn’t worry about it falling but then I went to clean the P365X after using it and I couldn’t get the slide off. Messed with it for a few minutes and couldn’t get it off. Once I locked the slide back and replaced it with the factory back plate, the slide came off with no issues. I wouldn’t recommend this for a P365X