POWERTEC Drill Press Table Accessories Kit w/T Track Drill Press Fence 14"x24",Laser Etched Scale, Clamps, Adjustable Inserts w/Knob, Flip Stops, Table Fence, Fits Tables 12" Above - 71539

Drilled about 30 1/2" holes through an aluminum bronze alloy (954, used in bearings, bushings and gears). This is a rather hard alloy with low heat coefficient of expansion. Bought two drill bits, expecting to use both, but drilled all with one. The last hole was as easy as the first. Great product. Smooth cutting. Very happy with the results, and would (and will) buy again.

The drill press table fits well on my drill press. the table and the drill press handle that moves the table up and down does get in the way of each other so I do have to move the table out of the way so the handle is free to move. Other than that I really like using the table, the clamps on the table and work nicely to hold down my wood when I'm drilling and the back board with the adjustable stop comes in real handy. It's nice not having to balance my wood with the little platform that my drill press came with. I would recommend.

I was looking at drill press tables and t-tracks for a new workbench I'm building and got lucky! I didn't want to put a WEN table on my 12" BILT HARD! Anyways, I am really grateful to come across PowerTec's t-track systems. I just started on my VERY 1st, personal (yes, it's not in someone's shop), track system and like the quality, value, and options. I made the mistake and purchased 24" sets from another company and totally regret it. The pics show better. Nevertheless, I am happy with Powertec. Great Job!

Hold downs won’t reach waste board in the middle of the table—t-tracks are too far away—DUH Powertec!🫤

Wonderfull drill press table! Easy setup.

works great, easily attached to drill press.

These were a disaster. Tape works much better. Some of them I couldn't even get to tighten on and once I finally did get one to tighten on it slipped when I was drilling. Waste of money.

After using the tiny table for years that came with my large radial drill press, I am very satisfied with now having a large work surface to fabricate with. This table, like most, I think, can be a bit fiddly to set up and adjust, but the price is well worth the time spent setting up your repeatable drilling projects. Read the other reviews that mention the problems with screws pulling out when you overtighten. I haven't replaced my screws yet, but that is on my list, and in the meantime, I have just paid attention to make sure I don't overtighten.

Excelente calidad del producto. Excelente terminado. Cumple la función para la que fué diseñado satisfactoriamente. Es un gran auxiliar en todo tipo de trabajos que realizó en mi taller, como por ejemplo me facilita el hacer orificios para adaptaciones de microswitches a los paneles de los microondas cuando se les daña la membrana. Mi base vino con tornillos y roscas que sostienen las tiras de aluminio. A diferencia de los modelos anteriores en los que el tornillo iba solamente dijo en la madera. Es un gran y útil producto para trabajar en el taller.

Was easy to assemble and install. I bought this for the drill press I want to purchase which is a larger unit with a large table top. For now I installed it on a smaller table top drill press and if fit perfectly. I have not tried drilling for cabinet door hinges yet but this unit should make it very easy to do. I would highly recommend this unit over the cheaper ones as this one comes with four hold down clamps and a swing down stop block.

Es un buen producto pero no se acopla a todas las marcas marca realice unos cortes y lo ajuste

Purchased with the intent to drill a 3/8 hole in 1/4 inch angle iron. Drilled a small pilot hole. Using a cordless drill the first bit snapped in half nearing the bottom of the hole. 2 of the remaining 3 also broke in half before drilling an entire hole. The 4th bit didn’t break I have used cobalt bits before and never had a 3/8 bit snap in half, especially using a cordless drill. These bits are terrible.

These drill bits pretend to be true cobalt. Good luck drilling stainless. Ok for aluminum.